
Home › Knowledge Hub › Kitchen Food Safety › Cleaning and Sanitising Commercial Kitchens in Aged Care
Kitchen Food Safety
By Lyndon Forrest, Managing Director · Clinically reviewed by Bridgette Mackie & Dianne Newey, Clinical Directors · May 2026 · Updated November 2026 · 10 min read
Cleaning and Sanitising Commercial Kitchens in Aged Care
TL;DR —
Cleaning and sanitising commercial kitchens in aged care are two distinct, sequential processes — both are required under FSANZ Food Safety Standard 3.2.2. Cleaning removes visible soil; sanitising reduces micro-organisms to safe levels. Food contact surfaces must be cleaned and sanitised before each use and at regular intervals. Thermal sanitising (a dishwasher reaching the manufacturer’s specified final rinse temperature) is preferred over chemical methods where possible. A documented cleaning schedule, covering benches, floors, equipment, cool rooms and exhaust hoods, is a practical way to meet the food safety program requirements for aged care. Pest management and food waste management are integral to kitchen hygiene. The ACSQHC Aged Care IPC Guide (2024) requires organic food waste to be stored away from food storage and preparation areas. During gastroenteritis outbreaks, cleaning frequency and methods must be escalated.

What Is the Difference Between Cleaning and Sanitising?
Cleaning and sanitising kitchens in aged care are two distinct processes that serve different purposes. Both are legally required under FSANZ Food Safety Standard 3.2.2. Neither process alone is sufficient — a surface must be cleaned before it can be effectively sanitised.
| Process | Definition | What It Achieves | What It Does Not Achieve |
|---|---|---|---|
| Cleaning | Removal of visible soil — food residue, grease, dirt, grime | Removes physical contamination; reduces microbial load by physically removing organisms | Does not reduce micro-organisms to safe levels on its own |
| Sanitising | Application of heat or chemicals to reduce micro-organisms to levels that do not compromise food safety | Reduces micro-organisms (bacteria, viruses) to safe levels | Does not remove physical soil — sanitiser cannot penetrate food residue effectively |
The correct sequence is always: pre-clean (remove loose debris), wash (detergent), rinse (clean water), sanitise (heat or chemical), air dry. Skipping any step compromises the effectiveness of the entire process.
This article is part of the Kitchen and Food Safety in Aged Care pillar
What Are Food Contact Surfaces vs Non-Food Contact Surfaces?
The distinction between food contact and non-food contact surfaces determines the level of cleaning and sanitising required. Food contact surfaces require both cleaning and sanitising. Non-food contact surfaces require regular cleaning and sanitising where contamination risk exists.
| Surface Type | Examples | Cleaning and Sanitising Requirement |
|---|---|---|
| Food contact surface | Chopping boards, bench tops, knives, mixing bowls, blender blades, serving utensils, trays, plates | Clean and sanitise before each use, after contamination, and at regular intervals during prolonged use |
| Non-food contact surface | Floors, walls, shelving, door handles, taps, oven exteriors, exhaust hoods | Clean regularly per schedule; sanitise where contamination risk exists (e.g., handles, taps) |
| Equipment internal surfaces | Cool room walls, oven interiors, microwave interiors, dishwasher interior | Clean per schedule; sanitise internal surfaces that contact food or food containers |
What Sanitising Methods Are Used in Aged Care Kitchens?
Two primary sanitising methods are used in aged care kitchens: thermal (heat) sanitising and chemical sanitising. Thermal sanitising is preferred where practical because it does not leave chemical residues and is consistently effective.
Need help implementing this in your facility? The IPS Hub gives your IPC Lead instant access to ready-made policies, procedures, and audit tools — updated monthly.
How Does Thermal Sanitising Work?
Thermal sanitising uses hot water at temperatures that kill micro-organisms. Safe Food Australia (4th edition, 2023) gives hot-water sanitising of at least 77°C for at least 30 seconds (or an equivalent time and temperature) for manual immersion. For commercial dishwashers, follow the manufacturer’s instructions for the wash and rinse cycle, which are designed to sanitise; many run a final rinse of about 80–85°C. Confirm the machine reaches its specified final rinse temperature.
| Method | Temperature | Contact Time | Application |
|---|---|---|---|
| Commercial dishwasher | Manufacturer’s specified final rinse temperature (many 80–85°C) | Manufacturer’s specified cycle | Crockery, cutlery, utensils, glassware |
| Hot water immersion | 77°C or above | 30 seconds immersion | Utensils, chopping boards, small equipment |
Commercial dishwashers in aged care must be monitored to confirm they reach the manufacturer’s specified final rinse temperature. Temperature should be checked daily using the machine’s built-in display or adhesive thermometer strips. Record results in the equipment monitoring log.
How Does Chemical Sanitising Work?
Chemical sanitising uses approved food-grade sanitisers to reduce micro-organisms. Chemical sanitisers are used where thermal sanitising is not practical — for example, large bench surfaces, equipment that cannot be immersed, or when hot water is unavailable.
Use only food-grade sanitisers approved for use on food contact surfaces
Follow the manufacturer’s instructions for dilution rate, contact time, and rinsing requirements
Common food-grade sanitisers include quaternary ammonium compounds (QACs) and sodium hypochlorite (bleach) at appropriate dilutions
Sanitiser must be applied to a pre-cleaned surface — sanitiser applied to a dirty surface is ineffective
Replace sanitiser solutions at the intervals specified by the manufacturer — solutions lose effectiveness over time
Never mix cleaning chemicals. Bleach mixed with acids (including some descalers and dishwasher products) releases chlorine gas, and mixed with ammonia-based products releases chloramines. Use one product at a time, rinse between products, wear gloves and eye protection when making up solutions, store chemicals away from food, and keep Safety Data Sheets available.
Sanitiser concentration can be checked using test strips specific to the sanitiser type
What Should a Kitchen Cleaning Schedule Include?
Standards 3.2.2 and 3.2.3 require food premises and equipment to be kept clean and food contact surfaces to be sanitised. Aged care providers serving vulnerable persons must also have a food safety program under Standard 3.3.1 (in NSW, under the Vulnerable Persons Food Safety Scheme), and a documented cleaning schedule is a practical way to meet it and show it to auditors. The cleaning schedule must specify what is cleaned, how often, the method, the products used, and who is responsible.
What Is the Recommended Cleaning Frequency for Kitchen Areas?
| Item / Area | Cleaning Frequency | Sanitising Frequency | Notes |
|---|---|---|---|
| Bench tops / food prep surfaces | After each use and between tasks | After each use | Use the 5-step process: pre-clean, wash, rinse, sanitise, air dry |
| Chopping boards | After each use | After each use | Colour-coded boards — separate for raw meat, cooked food, vegetables, dairy |
| Knives and utensils | After each use | After each use (via dishwasher or hot water immersion) | Sanitise between raw and ready-to-eat food use |
| Floors | Sweep after each service; wet clean daily | As needed (e.g., after spillage of fluids or food) | Non-slip flooring; coving at wall junctions |
| Walls and splashbacks | Weekly; immediately after splashing | After contamination events | Wipe down behind cooking stations daily |
| Stove tops and ovens | Wipe after each service; deep clean weekly | N/A (heat from use provides thermal sanitisation) | Remove grease buildup to prevent fire risk and pest attraction |
| Cool rooms | Daily wipe of shelves and handles; deep clean monthly | Monthly deep clean with sanitiser | Remove all food, clean shelving, walls, floor, check seals |
| Refrigerators | Daily wipe; deep clean weekly | Weekly with food-grade sanitiser | Check door seals; remove expired items during clean |
| Exhaust hoods and filters | Filters cleaned weekly; deep clean of hood system quarterly | N/A | Grease buildup is a fire hazard and pest attractant; engage licensed cleaner for duct cleaning |
| Dishwasher | Clean filter daily; deep clean weekly | Self-sanitising during use (77°C+) | Check spray arms, filters, and rinse temperature daily |
| Waste bins | Empty and wipe daily; deep clean weekly | Weekly with sanitiser | Foot-operated lids; lined; stored away from food prep areas |
| Hand wash basins | Clean daily | Sanitise daily | Must be kept clear of items; soap and paper towel stocked at all times |
The cleaning schedule must be displayed in the kitchen and include a sign-off system. Staff initial or sign against each task when completed. A supervisor should verify completion at least weekly. Unsigned or incomplete cleaning schedules are a common audit failure.
What Are the Dishwashing Requirements in Aged Care Kitchens?
Dishwashing in aged care kitchens serves both cleaning and sanitising functions. Commercial dishwashers that reach the manufacturer’s specified final rinse temperature are the preferred method because they achieve consistent, reliable sanitisation.
Pre-scrape food waste into bins before loading — do not rinse excessively (wastes water and reduces sanitiser effectiveness)
Load items to allow water and sanitiser contact on all surfaces — do not overload or nest items
Verify the final rinse reaches the manufacturer’s specified final rinse temperature; check daily and record
Clean dishwasher filter daily; clean spray arms, interior walls, and door seals weekly
Allow items to air dry in the machine or on a clean drying rack — do not use tea towels
Store clean crockery, cutlery, and utensils in clean, enclosed storage areas
What About Manual Dishwashing?
Manual dishwashing should be used only when a commercial dishwasher is unavailable or for items too large for the machine. Manual dishwashing requires a separate sanitising step:
Sink 1: Wash with hot water and detergent
Sink 2: Rinse with clean hot water
Sink 3: Sanitise by immersing items in water at 77°C or above for at least 30 seconds, using a rinsing basket or tongs and heat-resistant gloves (never bare hands), or use a food-grade chemical sanitiser per the manufacturer’s instructions
Air dry on a clean rack — do not stack wet items
How Should Pest Management Be Integrated with Kitchen Hygiene?
Pest management in aged care kitchens is a FSANZ Food Safety Standard 3.2.2 requirement. Pests — cockroaches, rodents, flies, ants, and stored product insects (e.g. beetles, weevils and moths), carry foodborne pathogens and contaminate food, surfaces, and equipment
Engage a licensed pest management provider for regular inspections and treatments — monthly at minimum for kitchens
Maintain pest-proof construction: self-closing doors, mesh screens on windows and vents, sealed pipe penetrations, no gaps under doors
Remove pest harbourage: eliminate clutter, seal cracks and crevices, fix moisture sources (leaking taps, condensation)
Eliminate food sources: clean up spillages immediately, store food in sealed containers, empty bins regularly
Monitor for pest activity: check traps, inspect deliveries, look for droppings, gnaw marks, or live pests
Document all pest management activities, inspections, treatments, and any pest sightings
Report any pest sighting in the kitchen through the incident reporting system — a single cockroach indicates a larger infestation
How Should Kitchen Waste Be Managed for IPC?
Waste management in aged care kitchens is an IPC requirement under the ACSQHC Aged Care IPC Guide (2024), which mandates that organic food waste must be stored away from food storage and preparation areas. Poor waste management attracts pests, creates odours, and increases contamination risk.
Kitchen bins must be foot-operated (hands-free), lined with plastic bags, and fitted with lids
Empty bins when three-quarters full — do not allow bins to overflow
Replace bin liners each time the bin is emptied
Clean and sanitise bins at least weekly, or more frequently if soiled
External waste storage areas must be located away from kitchen entries, food delivery areas, and air intake vents
External bins must be lidded, on a hard-standing surface, and cleaned regularly to prevent pest attraction
Separate waste streams where required: general waste, organic food waste, recyclables, and clinical waste (if applicable)
Food waste should not be left in the kitchen overnight — remove to external waste storage at end of each day
What Deep Cleaning Procedures Are Required?
Deep cleaning goes beyond the routine daily and weekly cleaning schedule. Deep cleaning of aged care kitchens should be scheduled at least quarterly and must include areas and equipment that are not addressed in daily cleaning.
Behind and underneath all fixed and movable equipment (stoves, fridges, benches)
Exhaust hoods, ductwork, and canopy filters (engage licensed cleaning contractor for ductwork)
Cool room walls, ceilings, floors, shelving, door seals, and drains
All ceiling tiles, light fittings, and ventilation grilles
Storage areas — dry goods store, chemical store, linen/uniform store
All drains, drain covers, and grease traps
Walls and ceiling above cooking areas — grease and condensation accumulate
Deep cleaning schedules must be documented and retained. Some deep cleaning tasks (e.g., exhaust duct cleaning) must be performed by licensed contractors and are subject to fire safety regulations.
How Should Kitchen Cleaning Change During Gastroenteritis Outbreaks?
During gastroenteritis outbreaks in aged care facilities, kitchen cleaning and sanitising must be escalated. The outbreak pathogen may be transmitted via contaminated surfaces, and standard cleaning routines may be insufficient.
Increase cleaning and sanitising frequency — food contact surfaces cleaned and sanitised after every use; dining tables and chairs cleaned and sanitised after every meal service
Use a chlorine-based product at the strength set in your outbreak management plan (commonly 1,000 ppm available chlorine) for hard surfaces. Quaternary ammonium products are not reliable against norovirus. Rinse food contact surfaces with clean water after the contact time and allow to air dry before food contact.
Clean and sanitise all frequently touched surfaces in the kitchen — door handles, taps, light switches, equipment controls — at least twice daily
Clean and sanitise food trolleys, meal trays, and transport containers after each use
Ensure dishwashers are reaching the manufacturer’s specified final rinse temperature; confirm and record the temperature at each wash cycle during outbreaks
Review and verify cleaning product dilution rates — incorrect dilution reduces effectiveness against outbreak pathogens
Assign dedicated cleaning staff to the kitchen during outbreaks where possible — avoid staff moving between clinical and kitchen areas
For comprehensive outbreak food safety procedures, see Food Safety During Outbreaks in Aged Care Facilities
For environmental cleaning during outbreaks, see Environmental Cleaning in Aged Care
Frequently Asked Questions
Can the same cloth be used for cleaning and sanitising?
No. Cleaning and sanitising are separate steps requiring separate cloths or a single-use disposable cloth replaced between steps. A cloth used for cleaning is contaminated with soil and micro-organisms — using the same cloth for sanitising recontaminates the surface. Best practice in aged care kitchens: use single-use disposable cloths or colour-coded microfibre cloths laundered at 60°C or above after each use.
What temperature must a commercial dishwasher reach for sanitising?
The final rinse must reach the manufacturer’s specified temperature. Many commercial dishwashers run a final rinse of about 80–85°C. Safe Food Australia (4th edition, 2023) gives 77°C for at least 30 seconds for manual hot-water immersion. The temperature should be verified daily using the machine’s display or adhesive thermometer strips and recorded in the equipment monitoring log.
How often should exhaust hood filters be cleaned?
Exhaust hood filters should be cleaned at least weekly in a commercial aged care kitchen. Exhaust ductwork requires deep cleaning by a licensed contractor at a frequency set by the applicable fire safety and ventilation standard and your usage; hood filters should be cleaned at least weekly. Grease buildup in exhaust systems is both a food safety risk (contamination) and a fire safety risk.
Is bleach safe to use on food contact surfaces?
Sodium hypochlorite (bleach) at the correct dilution (100–200 ppm for routine sanitising; 1,000 ppm during outbreaks) is an effective food-grade sanitiser. The surface must be rinsed with clean water after the required contact time before food contact resumes. Always follow manufacturer’s instructions for dilution, contact time, and rinsing.
What should be done if pest activity is found in the kitchen?
Report the sighting immediately through the facility’s incident system. Contact the pest management provider for an urgent inspection and treatment. Inspect all food storage areas for contamination — discard any food that shows signs of pest activity. Increase monitoring (check traps daily). Review and improve exclusion measures (seal gaps, fix screens). Document all actions taken.
References and Further Reading
The following authoritative sources inform the clinical and regulatory guidance in this article. Links open in a new tab.
- Food Standards Australia New Zealand. Food Safety Standards — Standard 3.2.2A Food Safety Management Tools. Canberra: FSANZ; 2023.
- Aged Care Quality and Safety Commission. Strengthened Aged Care Quality Standards 2025 — Standard 6: Food and Nutrition. Canberra: ACQSC; 2025.
- Australian Commission on Safety and Quality in Health Care. Infection Prevention and Control Guide for Residential Aged Care Facilities, Version 1.1. Sydney: ACSQHC; January 2025.
- Department of Health and Aged Care. Food safety requirements for aged care services. Canberra: Commonwealth of Australia; 2024.
- Communicable Diseases Network Australia. CDNA National Guidelines for the Public Health Management of Gastrointestinal Infections (incl. foodborne illness). Canberra: DoH; 2023.
In This Article
- What Is the Difference Between Cleaning and Sanitising?
- What Are Food Contact Surfaces vs Non-Food Contact Surfaces?
- What Sanitising Methods Are Used in Aged Care Kitchens?
- What Should a Kitchen Cleaning Schedule Include?
- What Are the Dishwashing Requirements in Aged Care Kitchens?
- How Should Pest Management Be Integrated with Kitchen Hygiene?
- How Should Kitchen Waste Be Managed for IPC?
- What Deep Cleaning Procedures Are Required?
- How Should Kitchen Cleaning Change During Gastroenteritis Outbreaks?
- Frequently Asked Questions

About the Author
Lyndon Forrest is the Managing Director of Bug Control — Infection Prevention Services, with over 30 years’ experience supporting aged care facilities across Australia and New Zealand with infection prevention, antimicrobial stewardship, and accreditation readiness.
Clinically reviewed by Bridgette Mackie & Dianne Newey, Clinical Directors
Ready to Strengthen Your Facility’s Infection Prevention?
The IPS Hub provides aged care facilities across Australia and New Zealand with continuously updated IPC policies, AMS tools, outbreak management resources, and direct support from experienced IPC professionals.


